All build areas

Build · Maple Ridge

Custom Homes & Renovations in Maple Ridge

Venture Pacific Construction Management is a custom home builder in Maple Ridge, building custom homes and completing major renovations for homeowners who want to update or rebuild rather than redevelop. Our work spans full teardown-and-rebuild custom homes, home renovations, home additions, heritage restorations, house lifts, and house moves, across Metro Vancouver and the Fraser Valley.

Project types
Custom homes, acreage builds, additions
Land
Larger lots, ALR in places
Sites
Sloped, treed, creek adjacent
Servicing
Septic and well on rural parcels

What we build in Maple Ridge

  • Custom home construction (full teardown-and-rebuild)
  • Home renovations
  • Home additions
  • Heritage home restoration
  • House lifts
  • House moves

Recent work

See recent examples of our custom home and renovation work.

View the portfolio

In short, Venture Pacific builds custom homes on acreage and subdivision lots in Maple Ridge and manages additions and renovations, working with riparian setbacks, steep slope requirements, and rural servicing.

Building a custom home in Maple Ridge: what the City asks for

A new house in Maple Ridge needs a City of Maple Ridge building permit, applied for online through the City's Citizen Portal. The City does not accept incomplete applications, and no building work may start before the permit is issued. Its new home construction page sets out three steps: plan, prepare, apply. It gives no review time. The wait depends on the number of applications the City is processing.

Planning starts with the lot. The City's Ridgeview map shows the zone, which sets what can be built, where it can sit and how much of the lot it can cover. Some single detached lots fall under the Urban Infill Residential use, where an eligible lot may hold three, four or six units depending on lot size, servicing, location and heritage status. Our post on Maple Ridge Urban Infill Residential explains those limits. Each lot gets one driveway, 4.0 m to 6.0 m wide at the property line, and each unit needs 2 parking stalls, one of them with the wiring for an electric vehicle charger put in during construction.

Rural lots and lots near creeks or slopes need more documents. The City's application checklist for up to six dwelling units (revised May 1, 2026) asks for a watercourse protection development permit for work within 50 metres of the top of bank of a watercourse or wetland, a geotechnical report when the lot is flagged as a geohazard area, and a flood hazard assessment with a flood construction level when it is flagged in a floodplain. A lot on a well needs an engineer's certificate that the well gives enough water and that it is safe to drink. A lot on septic needs a Fraser Health filing and a septic design sealed by an engineer. A single detached house in a wildfire development area is exempt from the wildfire development permit. It follows the City's wildfire construction requirements instead and may need a covenant on title. Every site also needs a stormwater management plan and an erosion and sediment control plan.

The drawings must be to scale and meet the BC Building Code and the Zoning Bylaw: site, floor, foundation, cross-section and roof plans, elevations, radon mitigation details, and structural drawings sealed by a professional engineer. The same checklist asks for a title search from the last 30 days, a BC Step Code compliance checklist and an energy model report for each building, a heat loss and heat gain calculation, an electrical load calculation, and the Homeowner Protection Office new home registration form. Since July 1, 2025, Maple Ridge has required Emissions Level 3 of the Zero Carbon Step Code for new houses, the level the Township of Langley also asks for on a Langley custom home.

During review, City staff list anything missing and say which charges apply, such as development cost charges, amenity cost charges, a damage deposit and engineering servicing fees. The permit is issued only when every City requirement is met and every fee is paid. One paper set of the approved drawings, full size and to scale, must be on site for each inspection. If the inspector cannot find it, the inspection has to be booked again and a re-inspection fee may apply.

Country Shop, in the photos below, is a detached workshop we built on a rural property in Langley. It is insulated and powered for use all year, and it took 4 months to build. For the permit steps in more detail, see our building permits guide. We read the City of Maple Ridge pages linked here on November 2, 2026.

How a new house gets a City of Maple Ridge building permit
  1. 01

    Plan

    Find the zone on the Ridgeview map, then check the units allowed, watercourses, slopes, protected trees, the driveway and parking.

  2. 02

    Prepare

    Drawings to scale under the BC Building Code and Zoning Bylaw, engineer reports where the lot is flagged, a Step Code checklist and energy model, and Emissions Level 3.

  3. 03

    Apply online

    Through the Citizen Portal. Incomplete applications are not accepted.

  4. 04

    City review

    Staff list missing items and the charges that apply. The City publishes no review time.

  5. 05

    Permit and inspections

    Issued once every requirement is met and every fee is paid. The approved drawings stay on site for each inspection.

Source: City of Maple Ridge, New Home Construction (updated August 25, 2026); Permit Application Checklist, Residential Up To Six Dwelling Units (revised May 1, 2026); BC Zero Carbon Step Code page (updated July 15, 2026)

Country Shop, Langley, photo 5Country Shop, Langley, photo 18Country Shop, Langley, photo 24
Country Shop, a detached workshop we built on a rural property in Langley: the side wall and high window, the covered patio, and the sliding door.See Country Shop

Custom homes with room to breathe

Silver Valley, Albion, and the rural parcels north of the town centre allow plans that a city lot never will: wide single-level homes, shops, covered outdoor space, real separation between the living and sleeping sides of the house.

What these sites ask in return is site work. Clearing, driveways, drainage, and sometimes long service runs come before anything else, and they belong in the budget from day one.

  • Custom homes on acreage and subdivision lots
  • Site clearing, driveway, and drainage planning
  • Septic design and well coordination where required
  • Additions and renovations to existing homes

Creeks, slopes, and environmental review

Maple Ridge has a great many watercourses, and riparian setbacks apply widely. Steep slope development permit areas also cover parts of the municipality, which affects how a house can be sited and what geotechnical work is required.

Both are identified early in our process, because they determine the buildable area and therefore the design.

Older Maple Ridge neighbourhoods

The older parts of Hammond, Port Haney, and the town centre have compact lots and homes from earlier eras, some with character worth keeping. Renovations there are more like our inner-municipality work: careful, constrained, and often full of surprises behind the lath.

We investigate before pricing on any house built before the 1960s, wherever it is.

Questions about building in Maple Ridge

Does Venture Pacific build custom homes in Maple Ridge?

Yes, Venture Pacific Construction Management builds full teardown-and-rebuild custom homes across Maple Ridge and throughout Metro Vancouver and the Fraser Valley. We manage the whole project ourselves, from the zoning and massing review through design coordination, permits, trades, and enrolment in the mandatory 2-5-10 new home warranty, so you deal with one builder from the first site visit to the final inspection.

Do you handle home renovations and additions in Maple Ridge?

Yes, Venture Pacific Construction Management completes full home renovations and additions across Maple Ridge and throughout Metro Vancouver and the Fraser Valley, from kitchen and bathroom remodels through second-storey and rear additions. We check the existing foundation and framing first, since what they can carry decides whether an addition or a full rebuild is the better route for the property.

Can you renovate or restore a heritage home in Maple Ridge?

Yes, we restore and renovate character and heritage homes across Maple Ridge and throughout Metro Vancouver and the Fraser Valley, keeping the street-facing form, trim profiles, and window proportions that give the house its value while rebuilding the insulation, wiring, and mechanical systems behind them. The result reads as the original house but performs and costs to run like a new one.

Do you offer house lifting or house moving services in Maple Ridge?

Yes, Venture Pacific Construction Management offers both services across Maple Ridge and throughout Metro Vancouver and the Fraser Valley. House lifting raises an existing home to add a basement or a new foundation level underneath it. House moving relocates a home to a new position on the same lot, or to a different property entirely, rather than demolishing and rebuilding.

What's the difference between Venture Pacific's construction and development work?

Venture Pacific Construction Management handles custom home building, renovations, additions, and heritage restorations for individual homeowners who keep their existing lot. Our separate development side designs and builds multiplex and missing-middle housing, triplexes through sixplexes, through a GP/LP partnership structure. Both sides operate across Metro Vancouver and the Fraser Valley.

Is it cheaper to build a custom home in Maple Ridge?

Land is significantly less expensive than the inner municipalities, which is why people build here rather than in a city lot they cannot afford. The house itself costs what it costs, and rural sites in Silver Valley and Albion add site work and servicing, so the full picture depends on the specific property.

Do I need a riparian assessment?

If your property is near one of Maple Ridge's many watercourses, yes. Riparian setbacks define the buildable area on the parcel, so this needs to be resolved by a qualified professional before the design is drawn, since it determines what can actually be built where.

Can you build on a steep Silver Valley lot?

Yes, steep slope development permit areas cover parts of Maple Ridge including Silver Valley, and those areas require geotechnical review and, often, engineered retaining before any excavation starts. We cost that work at the outset rather than letting it appear later as a change order.

How far out do you work?

We build throughout Maple Ridge, including rural and acreage properties in the north of the municipality around Silver Valley and Albion, and in older neighbourhoods like Hammond and Port Haney. If the drive from our base affects scheduling or cost, we say so plainly during the first conversation rather than after you have committed.

Let's talk about your property

A conversation, not a commitment.

Whether you're curious about the multiplex value of your land or looking to partner on a missing-middle build, we're here to start the conversation.